With the Core Ocean AiO, Alphacool presents an all-in-one solution that, thanks to its excellent price-performance ratio, enables entry into performance-oriented CPU water cooling. The difference to the Eisbaer CPU AiO is that the Ocean All-in-One is not expandable. Adding further components such as GPU coolers, radiators or expansion tanks is not intended here. But also not necessary! The choice of components and the design of the Core Ocean enable a long service life with low maintenance for water cooling of all common mainstream sockets from AMD and Intel.Aluminium RadiatorCompared to Alphacool's full copper models, the T38 aluminium radiator has additional cooling channels. This technical design allows a significant increase in cooling capacity without restricting the water flow within the radiator. Due to the low height of 38mm, the radiator with single-sided fan assembly fits into the tightest case and enables high-performance water cooling of the CPU.Core fanThe fan can be regulated from 0 to 2500 rpm via the 4-pin PWM connection. The cable is 40cm long. This allows the fan to be connected to the mainboard or a special controller without the need for additional adapter cables or extensions. At 2500 rpm, it provides an air flow of 62.8 CFM, together with a high static pressure of 2.13mm/H2O. This makes the fan perfect for mounting on radiators of a water cooling system.Cooler & PumpAs with all Alphacool products, the radiator base is made of copper and is equipped with very fine cooling fins distributed over the entire base. A nozzle plate ensures an accelerated flow over the cooling fins, which increases the cooling performance. The water flow is optimised so that all areas of the cooler base are cooled evenly. The cooler is compatible with all common mainstream sockets from AMD and Intel. The built-in pump has a speed range of 2500 - 3500 RPM (+/- 10%) and can be controlled via PWM. The pump is connected to the mainboard or to an external controller via the existing 4-pin fan connector. This allows the speed range of the pump to be controlled and monitored.Hoses & ConnectionsThe FEP hoses are 40cm long, sleeved and very flexible. The rotatable 360° connections to the cooler and to the radiator are permanently installed and cannot be replaced. However, the combination of hoses and connectors allows a very variable positioning of the AiO even in the tightest PC case.Illumination12 digitally addressable 5V RGB LEDs are installed in the pump housing, which create a unique, very noble-looking illumination. The digital aRGB LED lighting is connected via a JST 3-pin connector. To control the lighting, the 3-pin female connector must be connected to a digital RGB controller (not included) or a digital RGB-capable mainboard. Additional digital RGB LEDs can be connected to the remaining 3-pin male connector.Thermal compoundThe thermal paste included in the delivery has a thermal conductivity of 7.5 W/mK. The thermal grease does not harden, is particularly suitable for high contact pressures and can be applied perfectly due to the optimally selected viscosity. Compatibility:AMD: AM4 / AM5Intel: LGA 1150 / LGA 1200 / LGA 1700 / LGA 2066 Technical data radiatorL x W x H153 x 120 x 38mmMaterial cooling fins, channels & prechamber3003 AluminiumMaterial outer housing & threads3003 AluminiumFins per Inch19Fan size120mmFan slots1 one-sided / 2 double-sidedColorblackTechnical data fansL x W x H120 x 120 x 25mmBearing Typehydraulic BearingRated VoltageDC 12VOperating VoltageDC 7-14VStart-up Voltage7VRated Current0.23 (Max. 0.4) ARated Power2.76 (Max. 4.8) WRated Speed0 - 2500rpm/min (±10%)Max. Air Flow62.8CFMMax.Static Pressure2.13mm-H2ONoise level (rated voltage, mute room, distance 1m)33.0 (Max. 34.3) dBAMTBF50000hrs at 25°CSpeed Control ModePWMConnection & control4-pin PWM (cable 40cm)Auto-RestartyesTachometer OutputyesColorblackTechnical data cooler & pumpL x W x H70,2 x 70,2 x 46mmMaterial cooler bottomcopperMaterial pump housingSynthetic material (ABS+PC)Fin structure cooler bottom0,1 x 0,1mmMaterial pump bearing & shaftceramicsStarting voltage> DC 6VRated power7.1WNoise level35DbRated Current0.59A (±10% MAX)Speed2500~3500 (±10% RPM)Power supply Digital aRGB3-pin 5V (male & female, cable length 30cm)Number of aRGB LEDs12Power supply pump4-Pin JST (Kabellänge 30cm)Technical data tubesMaterialFEP, black with weave coverLength350mmWarranty: 3 years???? Warranty Terms
Effizienter 140-mm-PWM-Lüfter von SilverStone, Shark Force-Lüfterflügeldesign für geringere Geräuschemission und höhere Leistung, breiter Drehzahlbereich von 0 bis 2.200 U/min, modulares Kabelmanagement
140mm PWM fan, 15.5mm height suitable for small PC systems, rotational speed up to max. 1,700 RPM, 2mmH2O static air pressure, modular cable design, ARGB lighting
Average Particle Size: 0.49 micron (0.000020 inch) Peak: –50°C to 180°C Long-Term: –50°C to 130°C Performance:3 to 12 degrees centigrade lower CPU full load core temperatures than standard thermal compounds or thermal pads when measured with a calibrated thermal diode imbedded in the CPU core. Coverage Area:A 3.5 gram syringe contains enough compound to cover at least 15 to 25 small CPU cores, or 6 to 10 large CPU cores, or 2 to 5 heat plates. At a layer 0.003" thick, the 3.5 gram syringe will cover approximately 16 square inches. tootja lehel:http://www.arcticsilver.com/as5.htm
The holders for 120mm radiators from Bitspower extend the possibilities to accommodate radiators inside or outside the case. The black brackets are universally suitable for all 120mm fan radiators. Included in delivery are also the necessary screws for mounting. Technical Data: Color: Black Scope of delivery: Bitspower holder for 120mm radiators (2 angles), Screws
Toote kirjeldus inglise keeles:To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a matte black, straight adapter with two 1/4 inch external threads. In addition, the connection is rotatable, which significantly simplifies the screwing. Note: The turning function of the connections should always be used in the disassembled state, as this is relatively stiff due to the design. When installed, do not apply force to connections to avoid damaging the connectors themselves and the radiators on them. Technical details:Manufacturer's article no .: BP-MBRGMaterial: brassColor: matt blackConnections: male thread: 2x 1/4 inch
Toote kirjeldus inglise keeles:To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a matte black G1 / 4 inch screw for 16 / 10mm hoses, but can also be used for 16 / 11mm. The connection has an angle of 45 degrees and is double turnable. This greatly facilitates installation and allows for precise alignment. Note: The turning function of the connections should always be used in the disassembled state, as this is relatively stiff due to the design. When installed, do not apply force to connections to avoid damaging the connectors themselves and the radiators on them. Technical details:Material: brassColor: matt blackConnections: Thread: G1 / 4 inch Hose: 16/10 mm
To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a matte black, straight adapter with two G1 / 4-inch external threads. The special feature: The length of the adapter can be flexibly adjusted between 22 and 31 mm (measured without thread). For this purpose, only one nut is loosened, one side pulled out as desired and then fixed again with the union nut. Technical details:Material: brass, matt blackConnections: male thread: 2x G1 / 4 inchLength: 22 - 31 mm (variable)
The two clamp set is suitable for the equalizing tanks of the Z-series from Bitspower. They make it possible to mount the expansion tank individually inside or outside the case, also with the corresponding pump. The set contains two clamps each with four screws and nuts. The holders have an 80mm, 5mm high and 15mm deep base. The clamps themselves are 10mm wide, have an inside diameter of 60mm and an outside diameter of 66mm. Technical Data: Dimensions: 80 x 70 x 15 mm (W x H x D) Inner Diameter Clamps: 60 mm Outer Diameter Clamps: 66mm Material: Plastic Color: Black Compatibility: Bitspower water tanks of the Z-series
The None Chamfer PETG Link Tube in transparent by Bitspower is made of polyethylene terephthalate, PETG for short. This material is a plastic and is used, for example, for PET bottles. Its strength lies in its high break resistance, easy heatability and high stability. In order to implement them in the system, it is necessary to bend them into shape with heat and cut them to size. As a rule, the None Chamfer does not need to be reworked when it is cut. The tube measures 100cm in length, 12mm on the outside diameter and 10mm on the inside diameter. Only the EML series from Bitspower is compatible as connections. Technical Data: Material: PETG Color: Transparent Outer Diameter: 12 mm Inner Diameter: 10 mm Length: 100 cm Compatibility: EML series Bitspower connectors only
Toote kirjeldus inglise keeles:Dual panel-mounted socket threads for "internal/external" fittings on a computer chassis L-bracket. The female G 1/4 BSPP threaded couplings can be removed from the L-bracket and used as panel-mountable unions. Nickel-plated brass. This product may need to be temporarily disassembled during installation.
Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside or inside of the fan frame. If one of the two arrows points towards the interior or if the rotor suspension is aligned with the interior, this is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate.
DEMCiflex Dust Filter 120mm Round Black/White DF0525Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): Ø approx. 138 mmSize (filter): Ø approx. 113 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
120-mm-Gehäuselüfter, Drehgeschwindigkeit bis max. 2.000 U/min, maximale Lautstärke von 38,9 dB(A), 4-Pin-PWM-Anschluss, hohe Lebenserwartung von 70.000 Stunden
EK-Quantum Magnitude Accent - Purple is an interchangeable inner aesthetic frame for EK's new Magnitude water block. This purple accent is best used on Magnitude water blocks with translucent tops where the LED’s shine inwards, or for those without LED implementation. This Magnitude accent is made of anodized aluminum. Available in several different colors and materials, these accent frames are compatible only with EK-Quantum Magnitude CPU water blocks Made in Europe - Slovenia!
The Protium expansion tank from Singularity Computers is a 100mm tube with a diameter of 60mm. Together with the acrylic attachments, the expansion tank reaches a height of 139mm. It has a total of seven G1/4" ports and the tube itself is made of acrylic. Technical Data: Dimensions: 60 x 60 x 139 mm (L x W x H) Diameter: 60 mm Material: Acrylic (lid, base, reservoir), Aluminium (retention rings) Color: Black, Transparent Threads: 7x G1/4" Scope of Delivery: 1x 100 mm acrylic reservoir 2x Aluminium retention rings 1x 90° quad port cap (bottom) 1x Triple port cap (cover) 1x 16 mm internal acrylic flow standpipe 5x G1/4" stop fittings 2x Silicone O-rings
Verchromtes Wakü-Fitting von Phanteks mit zwei G1/4-Zoll-Gewinden (Male) zum Verbinden zweier GPU-Wasserkühler mit einem Abstand von 16 bis 22 Millimetern
EK-Quantum Vector Strix RX 6800/6900 is a 2nd generation Vector GPU water block from the EK® Quantum Line. It is made for ROG Strix RX 6800, 6800XT, 6900XT graphics cards based on the latest AMD® RDNA2™ architecture. EK-Quantum Vector Strix RX 6800/6900 water block for ROG Strix GAMING RX 6800 and 6900 GPUs EK-Quantum Vector RX 6800/6900 water block is compatible with ASUS® ROG Strix GAMING Radeon RX 6800, RX 6800XT, and 6900XT graphics cards. The Vector water block directly cools the GPU, VRAM, and the VRM (voltage regulation module) as a cooling liquid is channeled right over these critical areas. The water block is in contact with power stages as well as Inductor chokes to maximize cooling and minimize the chances of coil whine. These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The base of the block is CNC-machined out of high-grade nickel-plated electrolytic copper, while its top is CNC-machined out of durable black POM acetal. These 2nd generation Vector GPU water blocks also feature acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum Vector Strix RX 6800/6900 D-RGB water block The aesthetic end-piece is housing the addressable D-RGB LED strip. These water blocks boast a total of 9 individually addressable RGB LEDs, and a LED-lit terminal. They are compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the Strix 6800/6900 water block EK recommends the purchase of a retention backplate, which improves the overall aesthetics of your graphics cards, and also provides additional passive cooling for the GPU core and backside of the printed circuit board VRM and VRAM sections. Technical Specification Dimensions: (LxHxW) - 300.5x157x19.5mm Enclosed EK-Quantum Vector Strix RX 6800/6900 series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)
Backplate für GPU-Wasserkühlung, für EK-Quantum Vector Strix RX 6800/6900, aus vernickeltem Aluminium, bietet erhöhte Stabilität, mit Wärmeleitpad für passive Kühlung der PCB-Komponenten
Backplate für GPU-Wasserkühlung, für EK-Quantum Vector Strix RX 6800/6900, aus anodisiertem Aluminium, bietet erhöhte Stabilität, mit Wärmeleitpad für passive Kühlung der PCB-Komponenten
This is the 2nd generation Vector GPU water block from the EK® Quantum Line, designed for AORUS® Xtreme and Master RTX 3080 and 3090 graphics cards based on the latest NVIDIA® Ampere™ architecture. An EK water block for Xtreme and Master RTX 3080 and 3090 EK-Quantum Vector Xtreme 3080/3090 D-RGB - Nickel + Acetal water block is compatible with Aorus Xtreme and Master RTX 3080 and RTX 3090 graphics cards. The Vector water block actively cools the GPU, VRAM (on the front), power stages, and chokes in the VRM (voltage regulation module). These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The base of the block is CNC-machined out of nickel-plated high-grade copper, while its top is CNC-machined out of durable black POM Acetal. These 2nd generation Vector GPU water blocks also feature Acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum Vector Xtreme RTX 3080/3090 D-RGB water block The aesthetic corner end-piece is housing the addressable D-RGB LEDs. This water block boasts a total of 8 individually addressable RGB LEDs, and it is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the EK-Quantum Vector Xtreme 3080/3090 water block EK recommends the purchase of a retention backplate, especially for the 3090 models of graphics cards. The backplate improves the overall aesthetics of your graphics cards and also provides additional passive cooling for the GPU core, VRAM on the 3090 cards, and backside of the printed circuit board VRM section. Technical Specification Dimensions: (LxHxW) - 295x150.5x20.5mm Enclosed EK-Quantum Vector Xtreme RTX 3080/3090 D-RGB series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)
