This matt black T-splitter from Bitspower is made of brass and has three G1/4" internal threads. For example, a branch can be easily integrated into the main line of the water cooling system. Technical Data: Material: Brass Colour: Matt Black Connections: 3x G1/4" female thread Thread length: 5 mm
Full-Cover-Waterblock von EK Water Blocks, für EVGA XC3 RTX 3080 / 3080 Ti und 3090, vernickelter Kupferboden, Acetal-Deckel, adressierbare RGB-Beleuchtung
The CORSAIR iCUE H100i RGB ELITE series liquid CPU coolers offer first-class CPU cooling, integrated RGB lighting, and refined aesthetics, equipped with CORSAIR AF ELITE series PWM fans that deliver powerful airflow and specialized low-noise cooling modes.
Effizienter 140-mm-PWM-Lüfter von SilverStone, Shark Force-Lüfterflügeldesign für geringere Geräuschemission und höhere Leistung, breiter Drehzahlbereich von 0 bis 2.200 U/min, modulares Kabelmanagement
Average Particle Size: 0.49 micron (0.000020 inch) Peak: –50°C to 180°C Long-Term: –50°C to 130°C Performance:3 to 12 degrees centigrade lower CPU full load core temperatures than standard thermal compounds or thermal pads when measured with a calibrated thermal diode imbedded in the CPU core. Coverage Area:A 3.5 gram syringe contains enough compound to cover at least 15 to 25 small CPU cores, or 6 to 10 large CPU cores, or 2 to 5 heat plates. At a layer 0.003" thick, the 3.5 gram syringe will cover approximately 16 square inches. tootja lehel:http://www.arcticsilver.com/as5.htm
All metal inline coolant filter for keeping accidental debris from damaging the pump or clogging other components. It includes two reusable stainless steel filters with hole sizes of 0.42mm/sq and 0.27mm/sq.G 1/4 BSPP sockets are provided on both sides, with one male and one female for easy installation into the inlet of a water block, pump, or heat exchanger. Nickel-plated brass and stainless steel mesh filters. The filter body can be unscrewed for cleaning or replacement.Toote värvRoostevaba terasLaius32 mmSügavus23,3 mmKõrgus23,3 mmKaal70 g
Suurus:120 L x 120 W x 25 H mm tööpinge:3,5-13,8 V testitud:12V õhuvool:98 m3/h õhusurve:1,450 mm/H20 müratase:23,9 dBA kiirus:1500 RPM võimsustarve:1,80 W eestikeelne ülevaade:http://youtu.be/HnuOvu39nqk tootjalehel:http://www.blacknoise.com/en/products/it/17/Noiseblocker-NB_BlackSilentFan_120mm
To connect the individual components of the water cooling, the choice of the correct connections and their sufficient number is essential. Otherwise, installation will quickly become a frustrating experience if assembly fails on the wrong or too few connectors and is delayed due to this. Bitspower offers a comprehensive product range that offers the right solution for every requirement - whether adapters, direct hose connections, brackets or distributors. The design is solid and has a sealing ring. Thus, the connections remain tight and ensure high long-term durability. This is a matte black, straight adapter with two G1 / 4-inch external threads. The special feature: The length of the adapter can be flexibly adjusted between 22 and 31 mm (measured without thread). For this purpose, only one nut is loosened, one side pulled out as desired and then fixed again with the union nut. Technical details:Material: brass, matt blackConnections: male thread: 2x G1 / 4 inchLength: 22 - 31 mm (variable)
The two clamp set is suitable for the equalizing tanks of the Z-series from Bitspower. They make it possible to mount the expansion tank individually inside or outside the case, also with the corresponding pump. The set contains two clamps each with four screws and nuts. The holders have an 80mm, 5mm high and 15mm deep base. The clamps themselves are 10mm wide, have an inside diameter of 60mm and an outside diameter of 66mm. Technical Data: Dimensions: 80 x 70 x 15 mm (W x H x D) Inner Diameter Clamps: 60 mm Outer Diameter Clamps: 66mm Material: Plastic Color: Black Compatibility: Bitspower water tanks of the Z-series
Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside or inside of the fan frame. If one of the two arrows points towards the interior or if the rotor suspension is aligned with the interior, this is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate.
DEMCiflex Dust Filter 120mm Round Black/White DF0525Toote kirjeldus inglise keeles:If you open your PC again after half a year, perhaps to install new hardware, one wonders most of the time whether the Rechenknecht is not better to call a vacuum cleaner. What makes it easier on the one hand - imagine just how much more often the room would have to be cleaned if all the dirt was not collected as a precaution by the computer - means elsewhere consuming cleaning of the PC interior. In addition, dust in the housing is the main reason for overheating and thus for possible, unstable operation. Although a cleaning time-to-time can not be prevented, however, the effort can be significantly reduced. A simple and cost-effective solution are dust filters, which are placed in front of the sucking fans. Once installed, it is no longer necessary to dedust the entire interior with all its inaccessible corners and sensitive components, only the filters. DEMCiflex offers a particularly easy-to-retrofit solution, which in this case is suitable for 120 mm fans. Here, the filter is simply placed from the outside of the housing on the fan opening and is held there magnetically. There are therefore no screws or the like necessary, so there is no compatibility restriction. Since not all fan positions are magnetically attractive, an additional frame to the scope of delivery is glued to the back and on which the filter is held. The filter itself consists of a very tightly woven and durable polyester fabric. This special material is also used in clinics, for example to keep operating theaters dust-free. At the same time, the net is well permeable to air and therefore hinders the airflow only slightly. Of course, this effect diminishes with increasing dust, which is why the filter should occasionally be removed and cleaned. This is very simple in many ways. Firstly, it is easy to see if cleaning is necessary again - as soon as the white filter fabric has a gray haze, you should do this task. Due to the special mounting method, the removal of the fan is again very easy and fast. Afterwards, the dust can either be brushed, shaken, washed off and even scraped off with stubborn dirt. Finally, a few notes on the installation: First, the question arises, which fans have to be covered at all. As already mentioned, this applies exclusively to the sucking fans. But which are they? The safest way to recognize this is on the fan itself, with two arrows on the outside of the fan frame. If one of the two arrows points towards the interior, it is an aspirating fan. These are usually located on the front, side and bottom, whereas the rear and cover fans usually carry the air out of the housing and therefore need not be filtered. In order to maximize the filter effect, an overpressure in the housing can be generated. This means that more volume of air is forced into the housing than is being sucked out of the housing by other fans at the same time. This prevents air (and with it the dust) from entering the interior through other openings that may not have been filtered. If all fans are the same size, you should blow more fans into the housing than pull out. In this case, the power supply is to be counted as an additional, extracting fan, as long as it does not receive its supply (fan side) directly from the outside (occurs at floor mounting). If different fans with different sizes and speeds are used, the respective air volumes (m³ / h) in the data sheets give a good reference value, whereby in turn the total volume of the suction fans must be higher than that of the blowing out fans. Note: The area around the used fan slot should be flat if possible and have no protruding parts. Otherwise, these may impair adhesion to the substrate. Figure 4 shows an example configuration on a housing (not included). As can be seen, the use of LED fans is possible because the transparent material hardly hampers the lighting. Technical details:Size (frame): Ø approx. 138 mmSize (filter): Ø approx. 113 mmCompatibility: 120 mm fan slotMaterial (filter): polyester meshColor: black (frame), white (filter)Mounting: magnetic bracket + mounting frameAdvantages: Fast installation No compatibility restriction Easy and quick cleaning Effective filter effect with high air permeability Durable fabric
With the new compression fittings from Alphacool for Plexi, brass or carbon tubes, Alphacool is taking a further step towards perfection and quality. The first two colours, chrome and deep black, offer great variety. The fully coordinated product series allows each system to shine in its own right, and individuality has no limits when paired with the Alphacool Plexi and brass tubes! The colouring is bound fast to the brass surface with a new chromatization process. This ensures the longevity of the intense colour and prevents chipping of the chrome layer. An Alphacool logo on the connector emphasizes the distinctive nature of this product once again. The Function of this Connector is:This connector is used to connect two 16mm Plexi, brass or carbon tubes at a 90° angle. Dimensions: Width: 41.5mm Height: 41.5mm Technical Details: Material: brass, chromatized Colour: deep black Scope of Delivery: 1 x Alphacool HT 13mm HardTube Compression Fitting 90° L-Connector for Plexi, brass tubes - knurled - Deep black
Verchromtes Wakü-Fitting von Phanteks mit zwei G1/4-Zoll-Gewinden (Male) zum Verbinden zweier GPU-Wasserkühler mit einem Abstand von 16 bis 22 Millimetern
This is the 2nd generation Vector GPU water block from the EK® Quantum Line, designed for AORUS® Xtreme and Master RTX 3080 and 3090 graphics cards based on the latest NVIDIA® Ampere™ architecture. An EK water block for Xtreme and Master RTX 3080 and 3090 EK-Quantum Vector Xtreme 3080/3090 D-RGB - Nickel + Acetal water block is compatible with Aorus Xtreme and Master RTX 3080 and RTX 3090 graphics cards. The Vector water block actively cools the GPU, VRAM (on the front), power stages, and chokes in the VRM (voltage regulation module). These newly developed water blocks feature optimized flow paths that reduce hydrodynamic instabilities and vortexing (dead spots) inside of them. The EK-Quantum Vector Series water blocks use an Open Split-Flow cooling engine design, which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, meaning it can be used with weaker water pumps or pumps running on low-speed settings, and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performance when used in any given coolant flow orientation. The base of the block is CNC-machined out of nickel-plated high-grade copper, while its top is CNC-machined out of durable black POM Acetal. These 2nd generation Vector GPU water blocks also feature Acetal terminals. The watertight sealing is ensured by high-quality EPDM O-rings, while brass standoffs are already pre-installed and allow for a safe and easy installation procedure. D-RGB lighting on EK-Quantum Vector Xtreme RTX 3080/3090 D-RGB water block The aesthetic corner end-piece is housing the addressable D-RGB LEDs. This water block boasts a total of 8 individually addressable RGB LEDs, and it is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 3-pin D-RGB LED connector is to be aligned with the +5V marking on the D-RGB (addressable) header. Backplate for the EK-Quantum Vector Xtreme 3080/3090 water block EK recommends the purchase of a retention backplate, especially for the 3090 models of graphics cards. The backplate improves the overall aesthetics of your graphics cards and also provides additional passive cooling for the GPU core, VRAM on the 3090 cards, and backside of the printed circuit board VRM section. Technical Specification Dimensions: (LxHxW) - 295x150.5x20.5mm Enclosed EK-Quantum Vector Xtreme RTX 3080/3090 D-RGB series high-performance water block Mounting mechanism with screw-in brass standoffs Necessary mounting screws, nuts, and washers 2x Nickel plated brass plug G1/4” EK-Loop Multi Allen Key (6mm, 8mm, 9mm) Thermal pads Thermal grease EK-TIM Ectotherm (1g)
The CORSAIR H100 RGB all-in-one liquid CPU cooler delivers strong, dependable cooling and stunning lighting, with two CORSAIR SP120 RGB ELITE PWM fans, a 240mm radiator, and 29 RGB LEDs.
